Free to Air History
The first satellite television signal was relayed from Europe to the Telstar satellite over north america in 1962. The first geosynchronous communication satellite, Syncom 2, was launched in 1963. The world’s first commercial communication satellite, called Intelsat I (nicknamed Early Bird), was launched into synchronous orbit on April 6, 1965. The first national network of satellite television, called Orbita, was created in Soviet Union in 1967, and was based on the principle of using the highly elliptical Molniya satellite for re-broadcasting and delivering of TV signal to ground downlink stations. The first domestic North American satellite to carry television was Canada’s geostationary Anik 1, which was launched in 1972.[1]ATS-6, the world’s first experimental educational and Direct Broadcast Satellite, was launched in 1974. The first Soviet geostationary satellite to carry Direct-To-Home television, called Ekran, was launched in 1976.
Satellites used for television signals are generally in either naturally highly elliptical (with inclination of +/-63.4 degrees and orbital period of about 12 hours, also known as Molniya orbit) or geostationary orbit 37,000 km (22,300 miles) above the earth’s equator.
Satellite television, like other communications relayed by satellite, starts with a transmitting antenna located at an uplink facility. Uplink satellite dishes are very large, as much as 9 to 12 meters (30 to 40 feet) in diameter. The increased diameter results in more accurate aiming and increased signal strength at the satellite. The uplink dish is pointed toward a specific satellite and the uplinked signals are transmitted within a specific frequency range, so as to be received by one of the transponders tuned to that frequency range aboard that satellite. The transponder ‘retransmits’ the signals back to Earth but at a different frequency band (a process known as translation, used to avoid interference with the uplink signal), typically in the C-band (4–8 GHz) or Ku-band (12–18 GHz) or both. The leg of the signal path from the satellite to the receiving Earth station is called the downlink.
A typical satellite has up to 32 transponders for Ku-band and up to 24 for a C-band only satellite, or more for hybrid satellites. Typical transponders each have a bandwidth between 27 MHz and 50 MHz. Each geo-stationary C-band satellite needs to be spaced 2 degrees from the next satellite (to avoid interference). For Ku the spacing can be 1 degree. This means that there is an upper limit of 360/2 = 180 geostationary C-band satellites and 360/1 = 360 geostationary Ku-band satellites. C-band transmission is susceptible to terrestrial interference while Ku-band transmission is affected by rain (as water is an excellent absorber of microwaves at this particular frequency).
The downlinked satellite signal, quite weak after traveling the great distance (see inverse-square law), is collected by a parabolic receiving dish, which reflects the weak signal to the dish’s focal point. Mounted on brackets at the dish’s focal point is a device called a feedhorn. This feedhorn is essentially the flared front-end of a section of waveguide that gathers the signals at or near the focal point and ‘conducts’ them to a probe or pickup connected to a low-noise block downconverter or LNB. The LNB amplifies the relatively weak signals, filters the block of frequencies in which the satellite TV signals are transmitted, and converts the block of frequencies to a lower frequency range in the L-band range. The evolution of LNBs was one of necessity and invention.
The original C-Band satellite TV systems used a Low Noise Amplifier connected to the feedhorn at the focal point of the dish. The amplified signal was then fed via very expensive and sometimes 50 ohm impedance gas filled hardline coaxial cable to an indoor receiver or, in other designs, fed to a downconverter (a mixer and a voltage tuned oscillator with some filter circuitry) for downconversion to an intermediate frequency. The channel selection was controlled, typically by a voltage tuned oscillator with the tuning voltage being fed via a separate cable to the headend. But this design evolved.
Designs for microstrip based converters for Amateur Radio frequencies were adapted for the 4 GHz C-Band. Central to these designs was concept of block downconversion of a range of frequencies to a lower, and technologically more easily handled block of frequencies (intermediate frequency).
The advantages of using an LNB are that cheaper cable could be used to connect the indoor receiver with the satellite TV dish and LNB, and that the technology for handling the signal at L-Band and UHF was far cheaper than that for handling the signal at C-Band frequencies. The shift to cheaper technology from the 50 Ohm impedance cable and N-Connectors of the early C-Band systems to the cheaper 75 Ohm technology and F-Connectors allowed the early satellite TV receivers to use, what were in reality, modified UHF TV tuners which selected the satellite television channel for down conversion to another lower intermediate frequency centered on 70 MHz where it was demodulated. This shift allowed the satellite television DTH industry to change from being a largely hobbyist one where receivers were built in low numbers and complete systems were expensive (costing thousands of Dollars) to a far more commercial one of mass production.
Direct broadcast satellite dishes are fitted with an LNBF, which integrates the feedhorn with the LNB.
In the United States, service providers use the intermediate frequency ranges of 950-2150 MHz to carry the signal to the receiver. This allows for transmission of UHF band signals along the same span of coaxial wire at the same time. In some applications, (DirecTV AU9-S and AT-9) ranges the lower B-Band and upper 2250-3000 MHz, are used. Newer LNBFs in use by DirecTV referred to as SWM, use a more limited frequency range of 950-1800 MHz.
The satellite receiver or [Set-top box] demodulates and converts the signals to the desired form (outputs for television, audio, data, etc.). Sometimes, the receiver includes the capability to unscramble or decrypt the received signal; the receiver is then called an Integrated receiver/decoder or IRD. The cable connecting the receiver to the LNBF or LNB should be of the low loss type RG-6, quad shield RG-6 or RG-11, etc. RG-59 is not recommended for this application as it is not technically designed to carry frequencies above 950 MHz, but will work in many circumstances, depending on the quality of the coaxial wire.
Analog television distributed via satellite is usually sent scrambled or unscrambled in NTSC, PAL, or SECAM television broadcast standards. The analog signal is frequency modulated and is converted from an FM signal to what is referred to as baseband. This baseband comprises the video signal and the audio subcarrier(s). The audio subcarrier is further demodulated to provide a raw audio signal.
If the signal is a digitized television signal or multiplex of signals, it is typically QPSK.
In general, digital television, including that transmitted via satellites, are generally based on open standards such as MPEG and DVB-S or ISDB-S.
The conditional access encryption/scrambling methods include BISS, Conax, Digicipher, Irdeto, Nagravision, PowerVu, Viaccess, Videocipher, and VideoGuard. Many conditional access systems have been compromised.
